Μια βοήθεια,Πρόβλημα με το wifi μετά απο εγκατάσταση τον Μονομάχου 5!!!

Ανοιξε το τερματικο (Εφαρμογες - Βοηθηματα - Τερματικο) και δωσε τα αποτελεσματα απο

lspci -nn

iwconfig

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Για την πωτη εντολή ειναι:

user@ducatti-laptop:~$ lspci -nn
00:00.0 Host bridge [0600]: nVidia Corporation nForce3 Host Bridge [10de:00d1] (rev a4)
00:01.0 ISA bridge [0601]: nVidia Corporation nForce3 LPC Bridge [10de:00d0] (rev a6)
00:01.1 SMBus [0c05]: nVidia Corporation nForce3 SMBus [10de:00d4] (rev a4)
00:02.0 USB Controller [0c03]: nVidia Corporation nForce3 USB 1.1 [10de:00d7] (rev a5)
00:02.1 USB Controller [0c03]: nVidia Corporation nForce3 USB 1.1 [10de:00d7] (rev a5)
00:02.2 USB Controller [0c03]: nVidia Corporation nForce3 USB 2.0 [10de:00d8] (rev a2)
00:06.0 Multimedia audio controller [0401]: nVidia Corporation nForce3 Audio [10de:00da] (rev a2)
00:06.1 Modem [0703]: nVidia Corporation nForce3 Audio [10de:00d9] (rev a2)
00:08.0 IDE interface [0101]: nVidia Corporation nForce3 IDE [10de:00d5] (rev a5)
00:0a.0 PCI bridge [0604]: nVidia Corporation nForce3 PCI Bridge [10de:00dd] (rev a2)
00:0b.0 PCI bridge [0604]: nVidia Corporation nForce3 AGP Bridge [10de:00d2] (rev a4)
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV36 [GeForce FX Go5700] [10de:0348] (rev a1)
02:06.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet [14e4:169c] (rev 03)
02:07.0 CardBus bridge [0607]: Texas Instruments PCI4510 PC card Cardbus Controller [104c:ac44] (rev 02)
02:07.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCI4510 IEEE-1394 Controller [104c:8029]
02:08.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
user@ducatti-laptop:~$ ^C
user@ducatti-laptop:~$

Και για την δευτερη:

user@ducatti-laptop:~$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Συνδεσου με ethernet, καλωδιο, ανοιξε τερματικο, και εκτελεσε τις εντολες

sudo aptitude update
sudo aptitude install b43-fwcutter

Μετα κανε μια επανεκκινηση, και οταν μπεις, δες αν λειτουργει η ασυρματη καρτα!

Αν οχι, δωσε το αποτελεσμα της εντολης

dmesg

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Δε δουλευει φίλε μου,μετά την επανεκκίνηση,και μετά την εντολή dmesg βγάζει αυτά:

[ 0.000000] free_area_init_node: node 0, pgdat c080d700, node_mem_map c1001000

[ 0.000000] DMA zone: 32 pages used for memmap

[ 0.000000] DMA zone: 0 pages reserved

[ 0.000000] DMA zone: 3959 pages, LIFO batch:0

[ 0.000000] Normal zone: 1748 pages used for memmap

[ 0.000000] Normal zone: 221994 pages, LIFO batch:31

[ 0.000000] HighMem zone: 267 pages used for memmap

[ 0.000000] HighMem zone: 33895 pages, LIFO batch:7

[ 0.000000] Using APIC driver default

[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.

[ 0.000000] If you got timer trouble try acpi_use_timer_override

[ 0.000000] ACPI: PM-Timer IO Port: 0x8008

[ 0.000000] ACPI: Local APIC address 0xfee00000

[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)

[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])

[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])

[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23

[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

[ 0.000000] ACPI: IRQ9 used by override.

[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs

[ 0.000000] Using ACPI (MADT) for SMP configuration information

[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs

[ 0.000000] nr_irqs_gsi: 24

[ 0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000

[ 0.000000] PM: Registered nosave memory: 000000000009b000 - 000000000009c000

[ 0.000000] PM: Registered nosave memory: 000000000009c000 - 00000000000a0000

[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000

[ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 0000000000100000

[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:bff80000)

[ 0.000000] Booting paravirtualized kernel on bare hardware

[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1

[ 0.000000] PERCPU: Embedded 15 pages/cpu @c1a00000 s39320 r0 d22120 u2097152

[ 0.000000] pcpu-alloc: s39320 r0 d22120 u2097152 alloc=1*2097152

[ 0.000000] pcpu-alloc: [0] 0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259848

[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-13-generic-pae root=UUID=5a0712f3-d52d-41aa-8fca-29340cc87162 ro quiet splash

[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Enabling fast FPU save and restore... done.

[ 0.000000] Enabling unmasked SIMD FPU exception support... done.

[ 0.000000] Initializing CPU#0

[ 0.000000] allocated 5240000 bytes of page_cgroup

[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups

[ 0.000000] Initializing HighMem for node 0 (000379fe:0003ff70)

[ 0.000000] Memory: 1006760k/1048000k available (4934k kernel code, 40340k reserved, 2329k data, 676k init, 136648k highmem)

[ 0.000000] virtual kernel memory layout:

[ 0.000000] fixmap : 0xfff1d000 - 0xfffff000 ( 904 kB)

[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)

[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)

[ 0.000000] .init : 0xc0818000 - 0xc08c1000 ( 676 kB)

[ 0.000000] .data : 0xc05d1827 - 0xc0817e88 (2329 kB)

[ 0.000000] .text : 0xc0100000 - 0xc05d1827 (4934 kB)

[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.

[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] NR_IRQS:2304 nr_irqs:256

[ 0.000000] spurious 8259A interrupt: IRQ7.

[ 0.000000] Console: colour VGA+ 80x25

[ 0.000000] console [tty0] enabled

[ 0.000000] Fast TSC calibration using PIT

[ 0.000000] Detected 1794.992 MHz processor.

[ 0.008005] Calibrating delay loop (skipped), value calculated using timer frequency.. 3589.98 BogoMIPS (lpj=7179968)

[ 0.008031] Security Framework initialized

[ 0.008067] AppArmor: AppArmor initialized

[ 0.008076] Mount-cache hash table entries: 512

[ 0.008231] Initializing cgroup subsys ns

[ 0.008236] Initializing cgroup subsys cpuacct

[ 0.008241] Initializing cgroup subsys memory

[ 0.008251] Initializing cgroup subsys devices

[ 0.008254] Initializing cgroup subsys freezer

[ 0.008257] Initializing cgroup subsys net_cls

[ 0.008280] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)

[ 0.008283] CPU: L2 Cache: 1024K (64 bytes/line)

[ 0.008289] mce: CPU supports 5 MCE banks

[ 0.008313] Performance Events: AMD PMU driver.

[ 0.008319] ... version: 0

[ 0.008321] ... bit width: 48

[ 0.008324] ... generic registers: 4

[ 0.008326] ... value mask: 0000ffffffffffff

[ 0.008329] ... max period: 00007fffffffffff

[ 0.008331] ... fixed-purpose events: 0

[ 0.008333] ... event mask: 000000000000000f

[ 0.008338] Checking 'hlt' instruction... OK.

[ 0.024881] SMP alternatives: switching to UP code

[ 0.032338] Freeing SMP alternatives: 19k freed

[ 0.032355] ACPI: Core revision 20090903

[ 0.042797] ftrace: converting mcount calls to 0f 1f 44 00 00

[ 0.042816] ftrace: allocating 23424 entries in 46 pages

[ 0.044468] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1

[ 0.086231] CPU0: AMD Athlon 64 Processor 3000+ stepping 0a

[ 0.088001] Brought up 1 CPUs

[ 0.088001] Total of 1 processors activated (3589.98 BogoMIPS).

[ 0.088001] CPU0 attaching NULL sched-domain.

[ 0.088001] devtmpfs: initialized

[ 0.088001] regulator: core version 0.5

[ 0.088001] Time: 14:54:30 Date: 09/05/10

[ 0.088001] NET: Registered protocol family 16

[ 0.088001] EISA bus registered

[ 0.088001] ACPI: bus type pci registered

[ 0.088001] PCI: PCI BIOS revision 2.10 entry at 0xfd69c, last bus=2

[ 0.088001] PCI: Using configuration type 1 for base access

[ 0.088001] bio: create slab <bio-0> at 0

[ 0.088001] ACPI: EC: Look up EC in DSDT

[ 0.100096] ACPI: Interpreter enabled

[ 0.100103] ACPI: (supports S0 S3 S4 S5)

[ 0.100123] ACPI: Using IOAPIC for interrupt routing

[ 0.107158] ACPI: EC: GPE = 0x25, I/O: command/status = 0x66, data = 0x62

[ 0.107336] ACPI: No dock devices found.

[ 0.108650] ACPI: PCI Root Bridge [PCI0] (0000:00)

[ 0.108698] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xd8000000-0xdfffffff]

[ 0.108784] pci 0000:00:01.1: reg 20 io port: [0x2040-0x207f]

[ 0.108789] pci 0000:00:01.1: reg 24 io port: [0x2000-0x203f]

[ 0.108801] pci 0000:00:01.1: PME# supported from D3hot D3cold

[ 0.108804] pci 0000:00:01.1: PME# disabled

[ 0.108826] pci 0000:00:02.0: reg 10 32bit mmio: [0xd0000000-0xd0000fff]

[ 0.108846] pci 0000:00:02.0: supports D1 D2

[ 0.108848] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold

[ 0.108852] pci 0000:00:02.0: PME# disabled

[ 0.108870] pci 0000:00:02.1: reg 10 32bit mmio: [0xd0001000-0xd0001fff]

[ 0.108889] pci 0000:00:02.1: supports D1 D2

[ 0.108892] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold

[ 0.108895] pci 0000:00:02.1: PME# disabled

[ 0.108916] pci 0000:00:02.2: reg 10 32bit mmio: [0xd0004000-0xd00040ff]

[ 0.108939] pci 0000:00:02.2: supports D1 D2

[ 0.108942] pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold

[ 0.108946] pci 0000:00:02.2: PME# disabled

[ 0.108972] pci 0000:00:06.0: reg 10 io port: [0x1400-0x14ff]

[ 0.108976] pci 0000:00:06.0: reg 14 io port: [0x1c00-0x1c7f]

[ 0.108981] pci 0000:00:06.0: reg 18 32bit mmio: [0xd0002000-0xd0002fff]

[ 0.108997] pci 0000:00:06.0: supports D1 D2

[ 0.109015] pci 0000:00:06.1: reg 10 io port: [0x1800-0x18ff]

[ 0.109019] pci 0000:00:06.1: reg 14 io port: [0x1c80-0x1cff]

[ 0.109024] pci 0000:00:06.1: reg 18 32bit mmio: [0xd0003000-0xd0003fff]

[ 0.109041] pci 0000:00:06.1: PME# supported from D3cold

[ 0.109044] pci 0000:00:06.1: PME# disabled

[ 0.109072] pci 0000:00:08.0: reg 20 io port: [0x2080-0x208f]

[ 0.109235] pci 0000:02:06.0: reg 10 32bit mmio: [0xd0100000-0xd010ffff]

[ 0.109278] pci 0000:02:06.0: PME# supported from D3hot D3cold

[ 0.109282] pci 0000:02:06.0: PME# disabled

[ 0.109309] pci 0000:02:07.0: reg 10 32bit mmio: [0xd0116000-0xd0116fff]

[ 0.109324] pci 0000:02:07.0: supports D1 D2

[ 0.109326] pci 0000:02:07.0: PME# supported from D0 D1 D2 D3hot

[ 0.109330] pci 0000:02:07.0: PME# disabled

[ 0.109356] pci 0000:02:07.1: reg 10 32bit mmio: [0xd0117000-0xd01177ff]

[ 0.109362] pci 0000:02:07.1: reg 14 32bit mmio: [0xd0110000-0xd0113fff]

[ 0.109392] pci 0000:02:07.1: supports D1 D2

[ 0.109394] pci 0000:02:07.1: PME# supported from D0 D1 D2 D3hot

[ 0.109398] pci 0000:02:07.1: PME# disabled

[ 0.109421] pci 0000:02:08.0: reg 10 32bit mmio: [0xd0114000-0xd0115fff]

[ 0.109465] pci 0000:00:0a.0: bridge io port: [0x3000-0x3fff]

[ 0.109469] pci 0000:00:0a.0: bridge 32bit mmio: [0xd0100000-0xd04fffff]

[ 0.109516] pci 0000:01:00.0: reg 10 32bit mmio: [0xd1000000-0xd1ffffff]

[ 0.109523] pci 0000:01:00.0: reg 14 32bit mmio pref: [0xe0000000-0xefffffff]

[ 0.109544] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]

[ 0.109601] pci 0000:00:0b.0: bridge 32bit mmio: [0xd1000000-0xd1ffffff]

[ 0.109606] pci 0000:00:0b.0: bridge 32bit mmio pref: [0xe0000000-0xefffffff]

[ 0.109615] pci_bus 0000:00: on NUMA node 0

[ 0.109620] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

[ 0.109689] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]

[ 0.109723] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]

[ 0.120603] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0

[ 0.120764] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0

[ 0.120923] ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0

[ 0.121081] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0

[ 0.121238] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0

[ 0.121393] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21) *0

[ 0.121550] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21) *0

[ 0.121703] ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21) *0

[ 0.121861] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21) *0

[ 0.122018] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21) *0, disabled.

[ 0.122172] ACPI: PCI Interrupt Link [LACI] (IRQs 22) *0

[ 0.122325] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21) *0

[ 0.122482] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21) *0, disabled.

[ 0.122642] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21) *0, disabled.

[ 0.122752] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none

[ 0.122755] vgaarb: loaded

[ 0.122871] SCSI subsystem initialized

[ 0.122918] libata version 3.00 loaded.

[ 0.122988] usbcore: registered new interface driver usbfs

[ 0.123005] usbcore: registered new interface driver hub

[ 0.123031] usbcore: registered new device driver usb

[ 0.123154] ACPI: WMI: Mapper loaded

[ 0.123156] PCI: Using ACPI for IRQ routing

[ 0.123304] NetLabel: Initializing

[ 0.123307] NetLabel: domain hash size = 128

[ 0.123309] NetLabel: protocols = UNLABELED CIPSOv4

[ 0.123324] NetLabel: unlabeled traffic allowed by default

[ 0.123354] Switching to clocksource tsc

[ 0.123999] AppArmor: AppArmor Filesystem Enabled

[ 0.123999] pnp: PnP ACPI init

[ 0.123999] ACPI: bus type pnp registered

[ 0.126246] pnp: PnP ACPI: found 12 devices

[ 0.126249] ACPI: ACPI bus type pnp unregistered

[ 0.126253] PnPBIOS: Disabled by ACPI PNP

[ 0.126265] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved

[ 0.126270] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved

[ 0.126274] system 00:00: iomem range 0xfee00000-0xfeefffff has been reserved

[ 0.126278] system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved

[ 0.126285] system 00:02: ioport range 0x8000-0x807f has been reserved

[ 0.126289] system 00:02: ioport range 0x8080-0x80ff has been reserved

[ 0.126292] system 00:02: ioport range 0x8400-0x847f has been reserved

[ 0.126296] system 00:02: ioport range 0x8480-0x84ff has been reserved

[ 0.126300] system 00:02: ioport range 0x8800-0x887f has been reserved

[ 0.126303] system 00:02: ioport range 0x8880-0x88ff has been reserved

[ 0.126307] system 00:02: ioport range 0x2040-0x207f has been reserved

[ 0.126311] system 00:02: ioport range 0x2000-0x203f has been reserved

[ 0.126317] system 00:03: ioport range 0x4d0-0x4d1 has been reserved

[ 0.161032] pci 0000:02:07.0: BAR 16: can't allocate mem resource [0xd4000000-0xd04fffff]

[ 0.161036] pci 0000:02:07.0: CardBus bridge, secondary bus 0000:03

[ 0.161039] pci 0000:02:07.0: IO window: 0x003000-0x0030ff

[ 0.161045] pci 0000:02:07.0: IO window: 0x003400-0x0034ff

[ 0.161049] pci 0000:02:07.0: PREFETCH window: 0x40000000-0x43ffffff

[ 0.161054] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02

[ 0.161057] pci 0000:00:0a.0: IO window: 0x3000-0x3fff

[ 0.161061] pci 0000:00:0a.0: MEM window: 0xd0100000-0xd04fffff

[ 0.161065] pci 0000:00:0a.0: PREFETCH window: 0x40000000-0x43ffffff

[ 0.161072] pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xf0000000-0xefffffff]

[ 0.161075] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01

[ 0.161077] pci 0000:00:0b.0: IO window: disabled

[ 0.161082] pci 0000:00:0b.0: MEM window: 0xd1000000-0xd1ffffff

[ 0.161087] pci 0000:00:0b.0: PREFETCH window: 0xe0000000-0xefffffff

[ 0.161099] pci 0000:00:0a.0: setting latency timer to 64

[ 0.161107] pci 0000:02:07.0: enabling device (0106 -> 0107)

[ 0.161337] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 19

[ 0.161341] alloc irq_desc for 19 on node -1

[ 0.161344] alloc kstat_irqs on node -1

[ 0.161352] pci 0000:02:07.0: PCI INT A -> Link[LNK3] -> GSI 19 (level, low) -> IRQ 19

[ 0.161362] pci_bus 0000:00: resource 0 io: [0x00-0xffff]

[ 0.161365] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]

[ 0.161369] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]

[ 0.161372] pci_bus 0000:02: resource 1 mem: [0xd0100000-0xd04fffff]

[ 0.161375] pci_bus 0000:02: resource 2 pref mem [0x40000000-0x43ffffff]

[ 0.161379] pci_bus 0000:03: resource 0 io: [0x3000-0x30ff]

[ 0.161382] pci_bus 0000:03: resource 1 io: [0x3400-0x34ff]

[ 0.161385] pci_bus 0000:03: resource 2 pref mem [0x40000000-0x43ffffff]

[ 0.161388] pci_bus 0000:01: resource 1 mem: [0xd1000000-0xd1ffffff]

[ 0.161392] pci_bus 0000:01: resource 2 pref mem [0xe0000000-0xefffffff]

[ 0.161432] NET: Registered protocol family 2

[ 0.161537] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.161988] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

[ 0.163137] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)

[ 0.163707] TCP: Hash tables configured (established 131072 bind 65536)

[ 0.163710] TCP reno registered

[ 0.163822] NET: Registered protocol family 1

[ 0.588784] pci 0000:01:00.0: Boot video device

[ 0.588879] Simple Boot Flag at 0x36 set to 0x1

[ 0.589021] cpufreq-nforce2: No nForce2 chipset.

[ 0.589056] Scanning for low memory corruption every 60 seconds

[ 0.589195] audit: initializing netlink socket (disabled)

[ 0.589211] type=2000 audit(1283698469.588:1): initialized

[ 0.601059] Trying to unpack rootfs image as initramfs...

[ 0.613343] highmem bounce pool size: 64 pages

[ 0.613352] HugeTLB registered 2 MB page size, pre-allocated 0 pages

[ 0.618584] VFS: Disk quotas dquot_6.5.2

[ 0.618647] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[ 0.619282] fuse init (API version 7.13)

[ 0.619368] msgmni has been set to 1700

[ 0.624902] alg: No test for stdrng (krng)

[ 0.624913] io scheduler noop registered

[ 0.624916] io scheduler anticipatory registered

[ 0.624918] io scheduler deadline registered

[ 0.624979] io scheduler cfq registered (default)

[ 0.625114] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

[ 0.625138] pciehp: PCI Express Hot Plug Controller Driver version: 0.4

[ 0.625770] ACPI: AC Adapter [ACAD] (off-line)

[ 0.625846] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0

[ 0.625851] ACPI: Power Button [PWRB]

[ 0.625902] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1

[ 0.625948] ACPI: Lid Switch [LID]

[ 0.625997] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2

[ 0.626000] ACPI: Sleep Button [SLPB]

[ 0.626043] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3

[ 0.626046] ACPI: Power Button [PWRF]

[ 0.626248] Marking TSC unstable due to TSC halts in idle

[ 0.626294] processor LNXCPU:00: registered as cooling_device0

[ 0.630511] Switching to clocksource acpi_pm

[ 0.631507] thermal LNXTHERM:01: registered as thermal_zone0

[ 0.631516] ACPI: Thermal Zone [THRM] (47 C)

[ 0.633066] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[ 0.633196] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A

[ 0.633684] ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 21

[ 0.633691] alloc irq_desc for 21 on node -1

[ 0.633693] alloc kstat_irqs on node -1

[ 0.633705] serial 0000:00:06.1: PCI INT B -> Link[LMCI] -> GSI 21 (level, low) -> IRQ 21

[ 0.633712] serial 0000:00:06.1: PCI INT B disabled

[ 0.635434] brd: module loaded

[ 0.635941] loop: module loaded

[ 0.636044] input: Macintosh mouse button emulation as /devices/virtual/input/input4

[ 0.636368] pata_amd 0000:00:08.0: version 0.4.1

[ 0.636426] pata_amd 0000:00:08.0: setting latency timer to 64

[ 0.638389] ACPI: Battery Slot [BAT1] (battery absent)

[ 0.638400] isapnp: Scanning for PnP cards...

[ 0.643924] scsi0 : pata_amd

[ 0.648315] scsi1 : pata_amd

[ 0.648492] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2080 irq 14

[ 0.648496] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2088 irq 15

[ 0.649217] Fixed MDIO Bus: probed

[ 0.649254] PPP generic driver version 2.4.2

[ 0.649325] tun: Universal TUN/TAP device driver, 1.6

[ 0.649438] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 0.649712] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20

[ 0.649719] alloc irq_desc for 20 on node -1

[ 0.649721] alloc kstat_irqs on node -1

[ 0.649733] ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 20 (level, low) -> IRQ 20

[ 0.649761] ehci_hcd 0000:00:02.2: setting latency timer to 64

[ 0.649764] ehci_hcd 0000:00:02.2: EHCI Host Controller

[ 0.649800] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1

[ 0.649833] ehci_hcd 0000:00:02.2: debug port 1

[ 0.649840] ehci_hcd 0000:00:02.2: cache line size of 64 is not supported

[ 0.649863] ehci_hcd 0000:00:02.2: irq 20, io mem 0xd0004000

[ 0.693423] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00

[ 0.693524] usb usb1: configuration #1 chosen from 1 choice

[ 0.693556] hub 1-0:1.0: USB hub found

[ 0.693569] hub 1-0:1.0: 6 ports detected

[ 0.693625] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 0.693857] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21

[ 0.693861] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 21 (level, low) -> IRQ 21

[ 0.693870] ohci_hcd 0000:00:02.0: setting latency timer to 64

[ 0.693873] ohci_hcd 0000:00:02.0: OHCI Host Controller

[ 0.693906] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2

[ 0.693928] ohci_hcd 0000:00:02.0: irq 21, io mem 0xd0000000

[ 0.785595] usb usb2: configuration #1 chosen from 1 choice

[ 0.785638] hub 2-0:1.0: USB hub found

[ 0.785653] hub 2-0:1.0: 3 ports detected

[ 0.786008] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20

[ 0.786014] ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 20 (level, low) -> IRQ 20

[ 0.786039] ohci_hcd 0000:00:02.1: setting latency timer to 64

[ 0.786042] ohci_hcd 0000:00:02.1: OHCI Host Controller

[ 0.786085] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3

[ 0.786107] ohci_hcd 0000:00:02.1: irq 20, io mem 0xd0001000

[ 0.813181] ata1.00: ATA-6: IC25N060ATMR04-0, MO3OAD4A, max UDMA/100

[ 0.813187] ata1.00: 117210240 sectors, multi 16: LBA48

[ 0.813217] ata1: nv_mode_filter: 0x3f39f&0x7f39f->0x3f39f, BIOS=0x3f000 (0xc600c000) ACPI=0x7f01f (8:8:0x1b)

[ 0.872128] ata1.00: configured for UDMA/100

[ 0.874287] usb usb3: configuration #1 chosen from 1 choice

[ 0.874322] hub 3-0:1.0: USB hub found

[ 0.874339] hub 3-0:1.0: 3 ports detected

[ 0.874402] uhci_hcd: USB Universal Host Controller Interface driver

[ 0.874517] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12

[ 0.882513] serio: i8042 KBD port at 0x60,0x64 irq 1

[ 0.882520] serio: i8042 AUX port at 0x60,0x64 irq 12

[ 0.882676] mice: PS/2 mouse device common for all mice

[ 0.882896] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0

[ 0.882921] rtc0: alarms up to one year, y3k, 114 bytes nvram

[ 0.883040] device-mapper: uevent: version 1.0.3

[ 0.884123] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]

[ 0.888079] device-mapper: multipath: version 1.1.0 loaded

[ 0.888083] device-mapper: multipath round-robin: version 1.0.0 loaded

[ 0.888236] EISA: Probing bus 0 at eisa.0

[ 0.888246] Cannot allocate resource for EISA slot 1

[ 0.888248] Cannot allocate resource for EISA slot 2

[ 0.888251] Cannot allocate resource for EISA slot 3

[ 0.888262] Cannot allocate resource for EISA slot 8

[ 0.888265] EISA: Detected 0 cards.

[ 0.892157] cpuidle: using governor ladder

[ 0.892205] cpuidle: using governor menu

[ 0.892770] TCP cubic registered

[ 0.892947] NET: Registered protocol family 10

[ 0.893426] lo: Disabled Privacy Extensions

[ 0.893771] NET: Registered protocol family 17

[ 0.893803] powernow-k8: Found 1 AMD Athlon 64 Processor 3000+ processors (1 cpu cores) (version 2.20.00)

[ 0.893854] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x2

[ 0.893857] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6

[ 0.893860] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x12

[ 0.893907] Using IPI No-Shortcut mode

[ 0.894010] PM: Resume from disk failed.

[ 0.894025] registered taskstats version 1

[ 0.894263] Magic number: 10:767:939

[ 0.894366] rtc_cmos 00:06: setting system clock to 2010-09-05 14:54:30 UTC (1283698470)

[ 0.894370] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found

[ 0.894372] EDD information not available.

[ 0.914130] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5

[ 1.319578] isapnp: No Plug & Play device found

[ 1.319767] scsi 0:0:0:0: Direct-Access ATA IC25N060ATMR04-0 MO3O PQ: 0 ANSI: 5

[ 1.319977] sd 0:0:0:0: Attached scsi generic sg0 type 0

[ 1.320148] sd 0:0:0:0: [sda] 117210240 512-byte logical blocks: (60.0 GB/55.8 GiB)

[ 1.320195] sd 0:0:0:0: [sda] Write Protect is off

[ 1.320198] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

[ 1.320222] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 1.320358] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >

[ 1.378962] sd 0:0:0:0: [sda] Attached SCSI disk

[ 1.428288] usb 2-3: new full speed USB device using ohci_hcd and address 2

[ 1.484727] ata2.00: ATAPI: MATSHITADVD-RAM UJ-820S, 1.00, max UDMA/33

[ 1.484761] ata2: nv_mode_filter: 0x739f&0x7f39f->0x739f, BIOS=0x7000 (0xc600c000) ACPI=0x7f01f (8:8:0x1b)

[ 1.500690] ata2.00: configured for UDMA/33

[ 1.503610] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-820S 1.00 PQ: 0 ANSI: 5

[ 1.508141] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray

[ 1.508145] Uniform CD-ROM driver Revision: 3.20

[ 1.508265] sr 1:0:0:0: Attached scsi CD-ROM sr0

[ 1.508328] sr 1:0:0:0: Attached scsi generic sg1 type 5

[ 1.576706] Freeing initrd memory: 17468k freed

[ 1.596927] Freeing unused kernel memory: 676k freed

[ 1.597811] Write protecting the kernel text: 4936k

[ 1.597876] Write protecting the kernel read-only data: 1956k

[ 1.623118] ramzswap: disk size set to 512700 kB

[ 1.631710] udev: starting version 151

[ 1.643595] usb 2-3: configuration #1 chosen from 1 choice

[ 1.712825] Adding 512696k swap on /dev/ramzswap0. Priority:100 extents:1 across:512696k SS

[ 1.730806] Initializing USB Mass Storage driver...

[ 1.772821] scsi2 : SCSI emulation for USB Mass Storage devices

[ 1.828206] usbcore: registered new interface driver usb-storage

[ 1.828212] USB Mass Storage support registered.

[ 1.828310] usb-storage: device found at 2

[ 1.828312] usb-storage: waiting for device to settle before scanning

[ 1.903474] Linux agpgart interface v0.103

[ 1.911350] vga16fb: initializing

[ 1.911356] vga16fb: mapped to 0xc00a0000

[ 1.911433] fb0: VGA16 VGA frame buffer device

[ 1.915496] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:0e/LNXVIDEO:00/input/input6

[ 1.915537] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)

[ 1.919092] agpgart-amd64 0000:00:00.0: AGP bridge [10de/00d1]

[ 1.919119] agpgart-amd64 0000:00:00.0: aperture size 4096 MB is not right, using settings from NB

[ 1.919128] agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP

[ 1.928852] tg3.c:v3.102 (September 1, 2009)

[ 1.929189] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18

[ 1.929196] alloc irq_desc for 18 on node -1

[ 1.929199] alloc kstat_irqs on node -1

[ 1.929211] tg3 0000:02:06.0: PCI INT A -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18

[ 2.011094] agpgart-amd64 0000:00:00.0: AGP aperture is 128M @ 0xd8000000

[ 2.177665] eth0: Tigon3 [partno(BCM95788A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:c0:9f:42:1e:a7

[ 2.177670] eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0])

[ 2.177674] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]

[ 2.177676] eth0: dma_rwctrl[763f0000] dma_mask[32-bit]

[ 2.178014] ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 17

[ 2.178020] alloc irq_desc for 17 on node -1

[ 2.178023] alloc kstat_irqs on node -1

[ 2.178034] ohci1394 0000:02:07.1: PCI INT B -> Link[LNK5] -> GSI 17 (level, low) -> IRQ 17

[ 2.240509] Console: switching to colour frame buffer device 80x30

[ 2.250294] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[d0117000-d01177ff] Max Packet=[2048] IR/IT contexts=[4/8]

[ 3.520175] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00001b3175]

[ 3.862007] xor: automatically using best checksumming function: pIII_sse

[ 3.880011] pIII_sse : 5425.000 MB/sec

[ 3.880015] xor: using function: pIII_sse (5425.000 MB/sec)

[ 3.904079] device-mapper: dm-raid45: initialized v0.2594b

[ 4.097379] EXT4-fs (sda1): mounted filesystem with ordered data mode

[ 6.829539] usb-storage: device scan complete

[ 6.836657] scsi 2:0:0:0: Direct-Access Generic Flash R/W 2002 PQ: 0 ANSI: 2

[ 6.837082] sd 2:0:0:0: Attached scsi generic sg2 type 0

[ 6.858489] sd 2:0:0:0: [sdb] Attached SCSI removable disk

[ 20.757487] udev: starting version 151

[ 20.835061] Adding 1952760k swap on /dev/sda5. Priority:-1 extents:1 across:1952760k

[ 20.869963] lp: driver loaded but no devices found

[ 21.028582] i2c i2c-0: nForce2 SMBus adapter at 0x2040

[ 21.028607] i2c i2c-1: nForce2 SMBus adapter at 0x2000

[ 21.033495] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4

[ 21.339761] irda_init()

[ 21.339785] NET: Registered protocol family 23

[ 21.340536] parport_pc 00:0b: reported by Plug and Play ACPI

[ 21.340646] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]

[ 21.377690] acer-wmi: Acer Laptop ACPI-WMI Extras

[ 21.377706] acer-wmi: No or unsupported WMI interface, unable to load

[ 21.387965] yenta_cardbus 0000:02:07.0: CardBus bridge found [1025:0059]

[ 21.387988] yenta_cardbus 0000:02:07.0: Using CSCINT to route CSC interrupts to PCI

[ 21.387991] yenta_cardbus 0000:02:07.0: Routing CardBus interrupts to PCI

[ 21.387997] yenta_cardbus 0000:02:07.0: TI: mfunc 0x007c1b22, devctl 0x44

[ 21.401730] ppdev: user-space parallel port driver

[ 21.432276] lp0: using parport0 (interrupt-driven).

[ 21.433130] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.

[ 21.433176] nsc-ircc, chip->init

[ 21.433189] nsc-ircc, Found chip at base=0x04e

[ 21.433213] nsc-ircc, driver loaded (Dag Brattli)

[ 21.433220] nsc_ircc_open(), can't get iobase of 0x2f8

[ 21.433259] nsc-ircc, Found chip at base=0x04e

[ 21.433283] nsc-ircc, driver loaded (Dag Brattli)

[ 21.433287] nsc_ircc_open(), can't get iobase of 0x2f8

[ 21.433519] nsc-ircc 00:0a: disabled

[ 21.514084] type=1505 audit(1283687691.117:2): operation="profile_load" pid=639 name="/sbin/dhclient3"

[ 21.514412] type=1505 audit(1283687691.117:3): operation="profile_load" pid=639 name="/usr/lib/NetworkManager/nm-dhcp-client.action"

[ 21.514601] type=1505 audit(1283687691.117:4): operation="profile_load" pid=639 name="/usr/lib/connman/scripts/dhclient-script"

[ 21.620911] yenta_cardbus 0000:02:07.0: ISA IRQ mask 0x0c78, PCI irq 19

[ 21.620917] yenta_cardbus 0000:02:07.0: Socket status: 30000086

[ 21.620922] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06

[ 21.620933] yenta_cardbus 0000:02:07.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff

[ 21.620938] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x3fff: clean.

[ 21.621186] yenta_cardbus 0000:02:07.0: pcmcia: parent PCI bridge Memory window: 0xd0100000 - 0xd04fffff

[ 21.621190] yenta_cardbus 0000:02:07.0: pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff

[ 21.742923] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 22

[ 21.742932] alloc irq_desc for 22 on node -1

[ 21.742935] alloc kstat_irqs on node -1

[ 21.742946] Intel ICH 0000:00:06.0: PCI INT A -> Link[LACI] -> GSI 22 (level, low) -> IRQ 22

[ 21.743125] Intel ICH 0000:00:06.0: setting latency timer to 64

[ 21.879186] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006

[ 21.915820] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7

[ 21.970272] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.

[ 21.971543] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.

[ 21.972314] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.

[ 21.972941] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.

[ 21.973734] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.

[ 21.979858] EXT4-fs (sda6): mounted filesystem with ordered data mode

[ 22.316024] intel8x0_measure_ac97_clock: measured 55403 usecs (2688 samples)

[ 22.316030] intel8x0: clocking to 47488

[ 23.166089] type=1505 audit(1283687692.769:5): operation="profile_load" pid=802 name="/usr/share/gdm/guest-session/Xsession"

[ 23.173555] type=1505 audit(1283687692.777:6): operation="profile_replace" pid=804 name="/sbin/dhclient3"

[ 23.173901] type=1505 audit(1283687692.777:7): operation="profile_replace" pid=804 name="/usr/lib/NetworkManager/nm-dhcp-client.action"

[ 23.174086] type=1505 audit(1283687692.777:8): operation="profile_replace" pid=804 name="/usr/lib/connman/scripts/dhclient-script"

[ 23.189187] tg3 0000:02:06.0: firmware: requesting tigon/tg3_tso5.bin

[ 23.199788] type=1505 audit(1283687692.801:9): operation="profile_load" pid=806 name="/usr/bin/evince"

[ 23.204203] type=1505 audit(1283687692.809:10): operation="profile_load" pid=806 name="/usr/bin/evince-previewer"

[ 23.502687] type=1505 audit(1283687693.105:11): operation="profile_load" pid=806 name="/usr/bin/evince-thumbnailer"

[ 23.558647] ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 25.084934] tg3: eth0: Link is up at 100 Mbps, full duplex.

[ 25.084939] tg3: eth0: Flow control is off for TX and off for RX.

[ 25.085185] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[ 27.573132] ttyS1: LSR safety check engaged!

[ 35.888033] eth0: no IPv6 routers present

[ 37.154655] tg3: eth0: Link is down.

[ 83.677922] tg3: eth0: Link is up at 100 Mbps, full duplex.

[ 83.677927] tg3: eth0: Flow control is off for TX and off for RX.

user@ducatti-laptop:~$

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Πριν δοκιμασεις τα παρακατω, πες μας πως εχεις κανει την εγκατασταση, κανονικα ή μεσα απο τα παραθυρα(wubi) ?

Επισης δες το βιντεο εδω http://olympos.greeklug.gr/uploads/ubuntu/videos/prota_vimata.ogv

και κανε οπως λεει εκει τις ρυθμισεις στις Πηγες λογισμικου

και μετα κανε ενα update, λογικα μετα θα σου ζητησει να κανεις επανεκκινηση,

και δες μετα που θα μπεις, αν ειναι ενταξει!

Πριν την επανεκκινηση, θα πρεπει να εχεις στο ΟΝ το κουμπι για το ασυρματο!

Αν δεν φτιαξει, δες εδω http://ubuntuforums.org/showthread.php?t=1368699

το section Broadcom BCM4301/03/06/09 Hardware (B43 driver)

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Η εγκατάσταση είναι κανονική,και όχι με wubi μέσα απο τα windows.

φίλε μου έκανα ότι είπες με βάση το βίντεάκι που είδα,αλλά και πάλι δεν έγινε τπτ,τώρα θα προσπαθήσω να κάνω κάτιμε βάση την σελίδα βοήθειας που έδωσες.

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Να μην λέω χαζά αλλά δεν κατάλαβα τπτ,αν μπορείς με ποιο περιληπτικά λόγια να μου πεις τι να κανω,αν κατάλαβα καλά πρεπει να μπώ με liveusb και να κάνω

κατι ρυθμίσεις ίσως?να τρεξω κατι που θα βρω εκεί?δεν κατάλαβα,

Και ακόμη γμτ αφου εχει κανει τόσες αναβαθμίσεις,παλι μολις παω Συστημα->Δχση Συστήμστος->Οδηγοι Υλικού,το μονο που βρίσκει είναι η κάρττα γραφικών η οποια

χρησιμοποιει εξωτερικο οδηγο.

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Δες εδω https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#Installing%20BCM43xx%20drivers

αν δεν βγαλεις ακρια, πες να το κανουμε μαζι!

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Ανοιξε ενα τερματικο και δωσε:

sudo apt-get update
 
sudo apt-get install bcmwl-kernel-source

Μολις τελειωσει η εγκατασταση κανε επαννεκκινηση και θα πρεπει να δουλεψει η ασυρματη καρτα δικτυου.

www.ktmhellasclub.gr

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

tek640]

Ανοιξε ενα τερματικο και δωσε:
sudo apt-get update
 
sudo apt-get install bcmwl-kernel-source
Μολις τελειωσει η εγκατασταση κανε επαννεκκινηση και θα πρεπει να δουλεψει η ασυρματη καρτα δικτυου.

www.ktmhellasclub.gr

Το έκανα και αυτό φίλε μου αλλά συνεχίζει να μην βλέπει την καρτα δικτύου,και φυσικά να μην συνδεεται ασυρματα,αλλά εκτός απο αυτό,μετα απο αυτα που ειπες να κανω,τωρα πλεον δεν εκκινει με την πρωτη φορά αλλα κολλαει στην αρχη που λεει MONOMAXOS 5.0 εκκινει τουλαχιστον με την 4η φορά!

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Λόγο του ότι με βασάνισε κι εμένα αυτο το θέμα η λύση είναι απλή και εύκολη .....

Άνοιξε ένα τερματικό και δώσε:

sudo apt-get install bcmwl-kernel-source b43-fwcutter

Και μετά ....

sudo gedit /etc/modules

Και κάτω κάτω προσθέτεις .....

b43
ssb

Save

Restart και λογικά θα είμαστε Ο.Κ.

Special Thanks Στον φίλο μου "Τρίτωνα"

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

@tek640 & @Mivas

Αληθεια, γιατι προτεινετε το πακετο bcmwl-kernel-source

το οποιο δεν υποστηριζει τη σειρα BCM4306

Περισσοτερες πληροφοριες εδω https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx

και ακομα περισσοτερες εδω http://wireless.kernel.org/en/users/Drivers/b43

Η καρτα ειναι αυτη

02:08.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Γιατι εμενα στο netbook εχει καρτα broadcom 4311 και επαιξε μονο με αυτο το πακετο και τπτ αλλο.

www.ktmhellasclub.gr

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Φίλε μου Mivas ακόμα πειραματίζομαι,έκανα κι αυτά που είπες και εσύ αλλά τπτ ακόμα αρνείται πεισματικά να βρεί την κάρτα δικτύου.

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Φίλε
vagrale13 ,κοίταξα τα 2 link που έδωσες αλλά δεν.......ποια εντολή πρεπει να τρεξω απο εκει για να δει την κάρτα,ειναι τόσες πολλές που χάθηκα.Αν μπορείς όταν θα είσαι μέσα να το κάνουμε μαζι,θα ήμουν υποχρεωμένος.

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

@duc

Κανε απο synaptic απεγκατασταση το πακετο bcmwl-kernel-source

και μετα κανε τα βημματα που λεει εδω https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#Installing%20BCM43xx%20drivers

Απο εκει και κατω, δεν σε ενδιαφερει τι εχει παραπανω ο οδηγος, κανε τα

b43 - Internet access (οτι λεει)

b43 - No Internet access (κανε τα βημματα Step 1 και Step 2)

κανε επανεκκινηση, και δες αν λειτουργει!

Αν βρεις δυσκολια, πες να σου πω ακριβως τι να κανεις!

@tek640

Δεν εχετε την ιδια καρτα. Διαβασε λιγο τα link που σου εδωσα....

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Ειχα μεινει με την εντυπωση (λαθος βεβαια) οτι το πακετο bcmwl-kernel-source ειναι για ολες τις καρτες b43xx.

www.ktmhellasclub.gr

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

vagrale13]

@duc

Κανε απο synaptic απεγκατασταση το πακετο bcmwl-kernel-source

και μετα κανε τα βημματα που λεει εδω https://help.ubuntu.com/community/WifiDocs/Driver/bcm43xx#Installing%20BCM43xx%20drivers

Απο εκει και κατω, δεν σε ενδιαφερει τι εχει παραπανω ο οδηγος, κανε τα

b43 - Internet access (οτι λεει)

b43 - No Internet access (κανε τα βημματα Step 1 και Step 2)

κανε επανεκκινηση, και δες αν λειτουργει!

Αν βρεις δυσκολια, πες να σου πω ακριβως τι να κανεις!

@tek640

Δεν εχετε την ιδια καρτα. Διαβασε λιγο τα link που σου εδωσα....

vagrale13 ΦΙλε μου σε παρακαλω αν μπορεις να βοηθησεις γιατι δεν καταλαβα πως να τρεξω τα 2 αρχεια που κατεβασα!!!

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Εκτελεσε πρωτα, αν δεν το εχεις κανει,

sudo apt-get install b43-fwcutter

απαντησε στο ερωτημα ΝΑΙ

Μετα τα δυο αρχεια που κατεβασες βαλτα μεσα στο home σου, ανοιξε τερματικο και εκτελεσε τις τρεις εντολες

tar xfvj broadcom-wl-4.150.10.5.tar.bz2
sudo b43-fwcutter -w /lib/firmware wl_apsta-3.130.20.0.o
sudo b43-fwcutter --unsupported -w /lib/firmware broadcom-wl-4.150.10.5/driver/wl_apsta_mimo.o

κανε επανεκκινηση, και δες αν ειναι οκ!