Πρόβλημα σύνδεσης σε συγκεκριμένο δίκτυο με συγκεκριμένο netbook

Καλημέρα σε όλους
Έχω ενα live usb με mint 11 και αντιμετωπίζω το πιο κουλό προβλημα.
Δεν συνδέεται σε συγκεκριμένο δίκτυο (hot spot του δήμου)
Το ίδιο netbook με win συνδεεται κανονικότατα
Ποιο είναι το κουλο;Το ίδιο netbook σε άλλο δίκτυο με το stickaki
συνδέεται κανονικά
Τα περίεργα συνεχίζονται
Το ίδιο στικάκι σε αλλο laptop συνδέεται στο συγκεκριμένο δικτυο χωρίς πρόβλημα

mint@mint ~ $ lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8187SE Wireless LAN Controller (rev 22)

mint@mint ~ $ ifconfig
eth0 Link encap:Ethernet HWaddr 00:21:85:56:77:05
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:40 Base address:0xa000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:720 (720.0 B) TX bytes:720 (720.0 B)

wlan2     Link encap:Ethernet  HWaddr 00:21:85:bc:ed:f6
inet6 addr: fe80::221:85ff:febc:edf6/64 Scope:Link
UP BROADCAST MULTICAST  MTU:1500  Metric:1
RX packets:0 errors:0 dropped:18 overruns:0 frame:0
TX packets:564 errors:38 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B)  TX bytes:42093 (42.0 KB)
Interrupt:18 Memory:f8138000-f8138100 






mint@mint ~ $ iwconfig
lo        no wireless extensions.

eth0 no wireless extensions.

wlan2     802.11b/g  ESSID:"xanthi-hotspot"
Mode:Managed  Frequency=2.447 GHz  Access Point: Not-Associated
Bit Rate:54 Mb/s
Retry:on   RTS thr:off   Fragment thr:off
Power Management:off
Link Quality=0/100  Signal level=0 dBm  Noise level=0 dBm
Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
Tx excessive retries:0  Invalid misc:0   Missed beacon:0 



Αν και η iwconfig λέει ότι είμαι συνδεμένος στο xanthi hot spot 
συνδεση δεν υπάρχει

Φόρουμ

Βοήθεια με το Linux!

Δώσε αστέρια!

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Σχόλια

Αυτό είναι λογικό ρε παιδιά;

mint@mint / $ ifconfig
eth0 Link encap:Ethernet HWaddr 00:21:85:56:77:05
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:40 Base address:0xa000

wlan2 Link encap:Ethernet HWaddr 00:21:85:bc:ed:f6
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:61 errors:0 dropped:66 overruns:0 frame:0
TX packets:399 errors:28 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5063 (5.0 KB) TX bytes:30915 (30.9 KB)
Interrupt:18 Memory:f81e8000-f81e8100

Πως φέρνω την κάρτα στo default?
Υ.Γ Πως βάζω κώδικα στο post?

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Δες και το αποτελεσμα της εντολης

@dmesg@

και αν δεν βγαλεις ακρη, ανεβασε το να το δουμε!

Συνδεθείτε ή εγγραφείτε για να σχολιάσετε

Πιστευω να αντεγραψα το σωστο κομμάτι

45.086226] <30>udev[2229]: starting version 167
[ 45.963093] r8169 0000:01:00.0: eth0: link down
[ 45.977088] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 46.353976] intel_rng: FWH not detected
[ 46.626432] leds_ss4200: no LED devices found
[ 46.705809] r8187se: module is from the staging directory, the quality is unknown, you have been warned.
[ 47.088119] Linux video capture interface: v2.00
[ 47.090972] ieee80211_crypt: registered algorithm 'NULL'
[ 47.090983] ieee80211_crypt: registered algorithm 'TKIP'
[ 47.090990] ieee80211_crypt: registered algorithm 'CCMP'
[ 47.090997] ieee80211_crypt: registered algorithm 'WEP'
[ 47.091003]
[ 47.091005] Linux kernel driver for RTL8180 / RTL8185 based WLAN cards
[ 47.091012] Copyright (c) 2004-2005, Andrea Merello
[ 47.091017] r8180: Initializing module
[ 47.091022] r8180: Wireless extensions version 22
[ 47.091028] r8180: Initializing proc filesystem
[ 47.091097] r8180: Configuring chip resources
[ 47.091125] r8180 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 47.091140] r8180 0000:02:00.0: setting latency timer to 64
[ 47.098456] r8180: Channel plan is 2
[ 47.098461]
[ 47.098469] Dot11d_Init()
[ 47.098479] r8180: MAC controller is a RTL8187SE b/g
[ 47.100709] r8180: usValue is 0x100
[ 47.100714]
[ 47.143843] r8180: EEPROM version 104
[ 47.148213] r8180: WW:**PLEASE** REPORT SUCCESSFUL/UNSUCCESSFUL TO Realtek!
[ 47.151371] r8180: IRQ 18
[ 47.154187] r8180: Driver probe completed
[ 47.154194]
[ 47.673624] Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1, caps: 0xa04711/0xa00000/0x0
[ 47.741197] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
[ 48.174260] <30>udev[2299]: renamed network interface wlan0 to wlan2
[ 48.178950] r8180: Bringing up iface
[ 48.239583] uvcvideo: Found UVC 1.00 device BisonCam, NB Pro (5986:0203)
[ 48.258970] input: BisonCam, NB Pro as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/input/input7
[ 48.261751] usbcore: registered new interface driver uvcvideo
[ 48.261761] USB Video Class driver (v1.0.0)
[ 48.378016] r8180: Card successfully reset
[ 49.116396] r8180: WIRELESS_MODE_G
[ 49.116403]
[ 49.147296] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[ 49.301300] composite sync not supported
[ 49.338040] composite sync not supported
[ 49.460878] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[ 49.460891] atkbd serio0: Use 'setkeycodes e077 ' to make it known.
[ 49.464432] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[ 49.464446] atkbd serio0: Use 'setkeycodes e077 ' to make it known.
[ 49.947116] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 49.947241] HDA Intel 0000:00:1b.0: irq 41 for MSI/MSI-X
[ 49.947303] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 50.092586] hda_codec: ALC888: BIOS auto-probing.
[ 50.108364] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 50.109327] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 53.136638] lp: driver loaded but no devices found
[ 53.241333] ppdev: user-space parallel port driver
[ 55.288500] =>>>>>>>>>>=============================>set power:1, 72!
[ 56.893828] composite sync not supported
[ 56.931169] composite sync not supported
[ 56.978290] composite sync not supported
[ 57.016176] composite sync not supported
[ 63.873778] composite sync not supported
[ 75.905786] composite sync not supported
[ 77.419089] atkbd serio0: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[ 77.419103] atkbd serio0: Use 'setkeycodes e077 ' to make it known.
[ 77.422893] atkbd serio0: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[ 77.422905] atkbd serio0: Use 'setkeycodes e077 ' to make it known.
[ 79.669115] =>>>>>>>>>>=============================>set power:1, 143!
[ 350.705108] composite sync not supported
[ 972.082593] Linking with xanthi-hotspot: channel is 6
[ 972.123524] Linking with xanthi-hotspot: channel is 6
[ 974.640169] Linking with xanthi-hotspot: channel is 6
[ 974.661634] Associated successfully
[ 974.661648] Using G rates
[ 974.675939] ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
[ 985.456135] wlan2: no IPv6 routers present
[ 1020.272554] Linking with xanthi-hotspot: channel is 6
[ 1231.092528] composite sync not supported
[ 1291.909909] aufs au_new_inode:412:mintmenu[4350]: Warning: Un-notified UDBA or repeatedly renamed dir, b0, ext3, mint, hi71138, i260.
mint@mint ~ $