Καλησπέρα. Έχω την συγκεκριμένη Usb κάρτα και θέλω να βρω μια λύση ώστε να επεκτείνω τις usb πόρτες,
του κομπιούτερ μου γιατί η συγκεκριμένη μητρική (Asus P4p800SE) έχει 4 usb θύρες οι οποίες είναι usb 2.0/1.1.
Την κούμπωσα μέσα στο Pc και το Ubuntu 10.04, ενώ την βλέπει, όταν ανοίγω εξωτερικό σκληρό δίσκο ή φλασάκι
και πάω να αντιγράψω κάποιο μεγάλο αρχείο π.χ. avi από το φλασάκι στον εσωτερικό σκληρό, τότε ενώ αντιγράφει
και τον έχει κάνει προσάρτηση στην επιφάνεια εργασίας, ξαφνικά τον αποπροσαρτίζει και βγάζει σφάλμα αντιγραφής!
Σφάλμα I/O. Τι πρέπει να κάνω? Μήπως από το Bios να απενεργοποιήσω κάτι στις Usb ρυθμίσεις?
Ή χρειάζονται οδηγοί για την συγκεκριμένη κάρτα από το Ubuntu?
Αν μπορεί να βοηθήσει κάποιος, ευχαρίστως.
Φόρουμ
Δώσε αστέρια!
- Συνδεθείτε ή εγγραφείτε για να σχολιάσετε
Σχόλια
Δοκιμασε παλι να μεταφερεις καποιο μεγαλο αρχειο, και αν εχεις παλι το ιδιο σφαλμα, δωσε μας τι ακριβως γραφει, οπως και εκτελεσε την εντολη
και ποσταρε το αποτελεσμα της.
Καλησπέρα!
Το αποτέλεσμα της dmesg:
[ 0.231342] pnp: PnP ACPI: found 15 devices
[ 0.231348] ACPI: ACPI bus type pnp unregistered
[ 0.231355] ASUS P4P800 detected. Disabling PnPBIOS
[ 0.231359] PnPBIOS: Disabled
[ 0.231387] system 00:0b: ioport range 0x680-0x6ff has been reserved
[ 0.231393] system 00:0b: ioport range 0x290-0x297 has been reserved
[ 0.231406] system 00:0c: ioport range 0x4d0-0x4d1 has been reserved
[ 0.231412] system 00:0c: ioport range 0x800-0x87f has been reserved
[ 0.231417] system 00:0c: ioport range 0x480-0x4bf has been reserved
[ 0.231424] system 00:0c: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.231430] system 00:0c: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.231443] system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.231449] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.231462] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 0.231468] system 00:0e: iomem range 0xc0000-0xdffff could not be reserved
[ 0.231474] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[ 0.231480] system 00:0e: iomem range 0x100000-0x7ffeffff could not be reserved
[ 0.231486] system 00:0e: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.266392] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.266397] pci 0000:00:01.0: IO window: disabled
[ 0.266405] pci 0000:00:01.0: MEM window: 0xfc900000-0xfe9fffff
[ 0.266413] pci 0000:00:01.0: PREFETCH window: 0xe7e00000-0xf7efffff
[ 0.266423] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.266429] pci 0000:00:1e.0: IO window: 0xd000-0xdfff
[ 0.266437] pci 0000:00:1e.0: MEM window: 0xfea00000-0xfeafffff
[ 0.266444] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.266469] pci 0000:00:1e.0: setting latency timer to 64
[ 0.266476] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.266481] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.266487] pci_bus 0000:01: resource 1 mem: [0xfc900000-0xfe9fffff]
[ 0.266492] pci_bus 0000:01: resource 2 pref mem [0xe7e00000-0xf7efffff]
[ 0.266497] pci_bus 0000:02: resource 0 io: [0xd000-0xdfff]
[ 0.266502] pci_bus 0000:02: resource 1 mem: [0xfea00000-0xfeafffff]
[ 0.266507] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.266512] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.266578] NET: Registered protocol family 2
[ 0.266762] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.267368] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.268042] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.268382] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.268387] TCP reno registered
[ 0.268543] NET: Registered protocol family 1
[ 0.450902] Freeing initrd memory: 7801k freed
[ 1.868013] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 1.868156] pci 0000:01:00.0: Boot video device
[ 1.868449] cpufreq-nforce2: No nForce2 chipset.
[ 1.868490] Scanning for low memory corruption every 60 seconds
[ 1.868626] audit: initializing netlink socket (disabled)
[ 1.868651] type=2000 audit(1324080166.868:1): initialized
[ 1.877930] highmem bounce pool size: 64 pages
[ 1.877938] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.879933] VFS: Disk quotas dquot_6.5.2
[ 1.880030] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.880853] fuse init (API version 7.13)
[ 1.880979] msgmni has been set to 1705
[ 1.881323] alg: No test for stdrng (krng)
[ 1.881407] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.881412] io scheduler noop registered
[ 1.881415] io scheduler anticipatory registered
[ 1.881419] io scheduler deadline registered
[ 1.881483] io scheduler cfq registered (default)
[ 1.881640] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.881677] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.881805] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.881810] ACPI: Power Button [PWRB]
[ 1.881873] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.881877] ACPI: Power Button [PWRF]
[ 1.882125] processor LNXCPU:00: registered as cooling_device0
[ 1.882181] processor LNXCPU:01: registered as cooling_device1
[ 1.886002] isapnp: Scanning for PnP cards...
[ 1.888476] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.888586] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.888704] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.889164] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.889345] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.891298] brd: module loaded
[ 1.892188] loop: module loaded
[ 1.892327] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.892470] ata_piix 0000:00:1f.1: version 2.13
[ 1.892485] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[ 1.892495] alloc irq_desc for 18 on node -1
[ 1.892499] alloc kstat_irqs on node -1
[ 1.892509] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.892561] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.892674] scsi0 : ata_piix
[ 1.892799] scsi1 : ata_piix
[ 1.895294] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 1.895300] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 1.895330] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.895338] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 1.895388] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.895464] scsi2 : ata_piix
[ 1.895552] scsi3 : ata_piix
[ 1.895616] ata3: SATA max UDMA/133 cmd 0xeff0 ctl 0xefe4 bmdma 0xef60 irq 18
[ 1.895621] ata4: SATA max UDMA/133 cmd 0xefa8 ctl 0xefe0 bmdma 0xef68 irq 18
[ 1.896254] Fixed MDIO Bus: probed
[ 1.896317] PPP generic driver version 2.4.2
[ 1.896382] tun: Universal TUN/TAP device driver, 1.6
[ 1.896386] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.896532] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.896561] alloc irq_desc for 23 on node -1
[ 1.896564] alloc kstat_irqs on node -1
[ 1.896573] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 1.896592] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.896598] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.896668] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.896712] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.900588] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 1.900613] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebffc00
[ 1.916016] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.916172] usb usb1: configuration #1 chosen from 1 choice
[ 1.916223] hub 1-0:1.0: USB hub found
[ 1.916235] hub 1-0:1.0: 8 ports detected
[ 1.916334] alloc irq_desc for 20 on node -1
[ 1.916338] alloc kstat_irqs on node -1
[ 1.916346] ehci_hcd 0000:02:0a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 1.916361] ehci_hcd 0000:02:0a.2: EHCI Host Controller
[ 1.916417] ehci_hcd 0000:02:0a.2: new USB bus registered, assigned bus number 2
[ 1.916474] ehci_hcd 0000:02:0a.2: irq 20, io mem 0xfeafbc00
[ 1.928014] ehci_hcd 0000:02:0a.2: USB 2.0 started, EHCI 1.00
[ 1.928135] usb usb2: configuration #1 chosen from 1 choice
[ 1.928185] hub 2-0:1.0: USB hub found
[ 1.928199] hub 2-0:1.0: 4 ports detected
[ 1.928282] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.928309] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.928350] alloc irq_desc for 16 on node -1
[ 1.928353] alloc kstat_irqs on node -1
[ 1.928361] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.928370] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.928375] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.928430] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 1.928464] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ef00
[ 1.928608] usb usb3: configuration #1 chosen from 1 choice
[ 1.928654] hub 3-0:1.0: USB hub found
[ 1.928666] hub 3-0:1.0: 2 ports detected
[ 1.928738] alloc irq_desc for 19 on node -1
[ 1.928742] alloc kstat_irqs on node -1
[ 1.928754] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.928763] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.928768] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.928822] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[ 1.928855] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ef20
[ 1.929000] usb usb4: configuration #1 chosen from 1 choice
[ 1.929050] hub 4-0:1.0: USB hub found
[ 1.929061] hub 4-0:1.0: 2 ports detected
[ 1.929130] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.929139] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.929144] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.929198] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[ 1.929223] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef40
[ 1.929371] usb usb5: configuration #1 chosen from 1 choice
[ 1.929417] hub 5-0:1.0: USB hub found
[ 1.929428] hub 5-0:1.0: 2 ports detected
[ 1.929497] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.929506] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.929511] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.929576] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 6
[ 1.929601] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ef80
[ 1.929747] usb usb6: configuration #1 chosen from 1 choice
[ 1.929792] hub 6-0:1.0: USB hub found
[ 1.929803] hub 6-0:1.0: 2 ports detected
[ 1.929874] alloc irq_desc for 22 on node -1
[ 1.929878] alloc kstat_irqs on node -1
[ 1.929885] uhci_hcd 0000:02:0a.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1.929894] uhci_hcd 0000:02:0a.0: UHCI Host Controller
[ 1.929950] uhci_hcd 0000:02:0a.0: new USB bus registered, assigned bus number 7
[ 1.929983] uhci_hcd 0000:02:0a.0: irq 22, io base 0x0000df40
[ 1.930123] usb usb7: configuration #1 chosen from 1 choice
[ 1.930168] hub 7-0:1.0: USB hub found
[ 1.930178] hub 7-0:1.0: 2 ports detected
[ 1.930251] uhci_hcd 0000:02:0a.1: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[ 1.930260] uhci_hcd 0000:02:0a.1: UHCI Host Controller
[ 1.930322] uhci_hcd 0000:02:0a.1: new USB bus registered, assigned bus number 8
[ 1.930348] uhci_hcd 0000:02:0a.1: irq 23, io base 0x0000df80
[ 1.930491] usb usb8: configuration #1 chosen from 1 choice
[ 1.930536] hub 8-0:1.0: USB hub found
[ 1.930547] hub 8-0:1.0: 2 ports detected
[ 1.930704] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.932975] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.932987] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.933201] mice: PS/2 mouse device common for all mice
[ 1.933390] rtc_cmos 00:02: RTC can wake from S4
[ 1.933453] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.933479] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 1.933670] device-mapper: uevent: version 1.0.3
[ 1.933839] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[ 1.933956] device-mapper: multipath: version 1.1.0 loaded
[ 1.933960] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.934151] EISA: Probing bus 0 at eisa.0
[ 1.934193] EISA: Detected 0 cards.
[ 1.934313] cpuidle: using governor ladder
[ 1.934317] cpuidle: using governor menu
[ 1.935062] TCP cubic registered
[ 1.935303] NET: Registered protocol family 10
[ 1.936737] NET: Registered protocol family 17
[ 1.936812] Using IPI No-Shortcut mode
[ 1.936947] PM: Resume from disk failed.
[ 1.936966] registered taskstats version 1
[ 1.937297] Magic number: 7:272:1
[ 1.937389] rtc_cmos 00:02: setting system clock to 2011-12-17 00:02:47 UTC (1324080167)
[ 1.937395] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.937398] EDD information not available.
[ 1.956335] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.068865] ata4.00: ATA-7: WDC WD800JD-00MSA1, 10.01E01, max UDMA/133
[ 2.068871] ata4.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.069072] ata1.00: ATAPI: HL-DT-STDVD-RAM GH22LP20, 2.00, max UDMA/66
[ 2.069147] ata1.01: ATAPI: ATAPI DVD-ROM 16XMax, VER 1.16, max UDMA/33
[ 2.076589] ata3.00: HPA unlocked: 156247887 -> 156250000, native 156250000
[ 2.076597] ata3.00: ATA-7: WDC WD800JD-75MSA1, 10.01E01, max UDMA/133
[ 2.076602] ata3.00: 156250000 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.076841] ata1.00: configured for UDMA/66
[ 2.076949] ata4.00: configured for UDMA/133
[ 2.084477] ata1.01: configured for UDMA/33
[ 2.084572] ata3.00: configured for UDMA/133
[ 2.239794] isapnp: No Plug & Play device found
[ 2.241015] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD-RAM GH22LP20 2.00 PQ: 0 ANSI: 5
[ 2.244551] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.244556] Uniform CD-ROM driver Revision: 3.20
[ 2.244684] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 2.244758] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 2.245117] scsi 0:0:1:0: CD-ROM ATAPI DVD-ROM 16XMax 1.16 PQ: 0 ANSI: 5
[ 2.247007] sr1: scsi3-mmc drive: 0x/48x cd/rw xa/form2 cdda tray
[ 2.247108] sr 0:0:1:0: Attached scsi CD-ROM sr1
[ 2.247172] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 2.247361] scsi 2:0:0:0: Direct-Access ATA WDC WD800JD-75MS 10.0 PQ: 0 ANSI: 5
[ 2.247531] sd 2:0:0:0: [sda] 156250000 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.247559] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 2.247682] sd 2:0:0:0: [sda] Write Protect is off
[ 2.247688] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.247745] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.247753] scsi 3:0:0:0: Direct-Access ATA WDC WD800JD-00MS 10.0 PQ: 0 ANSI: 5
[ 2.247989] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 2.248037] sda:
[ 2.248159] sd 3:0:0:0: [sdb] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.248256] sd 3:0:0:0: [sdb] Write Protect is off
[ 2.248261] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.248309] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.248534] sdb: sdb1
[ 2.256290] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 2.267238] sda1 sda2 sda3
[ 2.282142] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.282170] Freeing unused kernel memory: 668k freed
[ 2.282678] Write protecting the kernel text: 4684k
[ 2.282732] Write protecting the kernel read-only data: 1844k
[ 2.308253] udev: starting version 151
[ 2.412093] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 2.449914] skge 0000:02:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 2.449965] skge 1.13 addr 0xfeafc000 irq 22 chip Yukon-Lite rev 7
[ 2.451281] skge eth0: addr 00:0e:a6:8f:ec:e3
[ 2.526086] Floppy drive(s): fd0 is 1.44M
[ 2.544832] FDC 0 is a post-1991 82077
[ 2.760302] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 3.198734] usb 4-1: configuration #1 chosen from 1 choice
[ 14.453336] Adding 4610644k swap on /dev/sda2. Priority:-1 extents:1 across:4610644k
[ 14.478864] udev: starting version 151
[ 14.604390] lp: driver loaded but no devices found
[ 14.639755] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.771543] Linux agpgart interface v0.103
[ 14.848367] parport_pc 00:0a: reported by Plug and Play ACPI
[ 14.848415] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 14.849314] agpgart-intel 0000:00:00.0: Intel 865 Chipset
[ 14.868408] intel_rng: FWH not detected
[ 14.891233] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 14.910986] usbcore: registered new interface driver hiddev
[ 14.925869] vga16fb: initializing
[ 14.925876] vga16fb: mapped to 0xc00a0000
[ 14.925980] fb0: VGA16 VGA frame buffer device
[ 14.944359] lp0: using parport0 (interrupt-driven).
[ 14.996988] nvidia: module license 'NVIDIA' taints kernel.
[ 14.996994] Disabling lock debugging due to kernel taint
[ 15.165830] type=1505 audit(1324072980.726:2): operation="profile_load" pid=558 name="/sbin/dhclient3"
[ 15.166705] type=1505 audit(1324072980.726:3): operation="profile_load" pid=558 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 15.167194] type=1505 audit(1324072980.726:4): operation="profile_load" pid=558 name="/usr/lib/connman/scripts/dhclient-script"
[ 15.169536] type=1505 audit(1324072980.730:5): operation="profile_replace" pid=560 name="/sbin/dhclient3"
[ 15.170418] type=1505 audit(1324072980.730:6): operation="profile_replace" pid=560 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 15.170912] type=1505 audit(1324072980.730:7): operation="profile_replace" pid=560 name="/usr/lib/connman/scripts/dhclient-script"
[ 15.239542] psmouse serio1: ID: 10 00 64
[ 15.313074] ppdev: user-space parallel port driver
[ 15.457224] Console: switching to colour frame buffer device 80x30
[ 15.588040] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 15.588054] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 15.589415] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.17 Thu Apr 15 05:28:41 PDT 2010
[ 15.698912] C-Media PCI 0000:02:0c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 15.711600] EXT4-fs (sda3): mounted filesystem with ordered data mode
[ 16.029318] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input4
[ 16.820723] generic-usb 0003:0463:FFFF.0001: hiddev96,hidraw0: USB HID v1.00 Device [EATON NOVA AVR] on usb-0000:00:1d.1-1/input0
[ 16.820781] usbcore: registered new interface driver usbhid
[ 16.820789] usbhid: v2.6:USB HID core driver
[ 18.250301] type=1505 audit(1324072983.810:8): operation="profile_load" pid=786 name="/usr/share/gdm/guest-session/Xsession"
[ 18.250766] type=1505 audit(1324072983.810:9): operation="profile_replace" pid=787 name="/sbin/dhclient3"
[ 18.251913] type=1505 audit(1324072983.810:10): operation="profile_replace" pid=787 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 18.252417] type=1505 audit(1324072983.814:11): operation="profile_replace" pid=787 name="/usr/lib/connman/scripts/dhclient-script"
[ 18.299586] skge eth0: enabling interface
[ 18.303317] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.636154] agpgart-intel 0000:00:00.0: AGP 3.0 bridge
[ 18.636173] agpgart-intel 0000:00:00.0: bridge is in legacy mode, falling back to 2.x
[ 18.636183] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[ 18.636226] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 19.865591] CPU0 attaching NULL sched-domain.
[ 19.865602] CPU1 attaching NULL sched-domain.
[ 19.901111] CPU0 attaching sched-domain:
[ 19.901120] domain 0: span 0-1 level SIBLING
[ 19.901126] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 19.901140] domain 1: span 0-1 level MC
[ 19.901146] groups: 0-1 (cpu_power = 1178)
[ 19.901159] CPU1 attaching sched-domain:
[ 19.901164] domain 0: span 0-1 level SIBLING
[ 19.901169] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 19.901181] domain 1: span 0-1 level MC
[ 19.901187] groups: 0-1 (cpu_power = 1178)
[ 20.041475] skge eth0: Link is up at 100 Mbps, full duplex, flow control none
[ 20.041931] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.341204] CPU0 attaching NULL sched-domain.
[ 23.341215] CPU1 attaching NULL sched-domain.
[ 23.361102] CPU0 attaching sched-domain:
[ 23.361110] domain 0: span 0-1 level SIBLING
[ 23.361115] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 23.361126] domain 1: span 0-1 level MC
[ 23.361130] groups: 0-1 (cpu_power = 1178)
[ 23.361141] CPU1 attaching sched-domain:
[ 23.361147] domain 0: span 0-1 level SIBLING
[ 23.361151] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 23.361161] domain 1: span 0-1 level MC
[ 23.361166] groups: 0-1 (cpu_power = 1178)
[ 30.880013] eth0: no IPv6 routers present
[ 79.280022] usb 2-1: new high speed USB device using ehci_hcd and address 2
[ 79.492269] usb 2-1: configuration #1 chosen from 1 choice
[ 79.508492] Initializing USB Mass Storage driver...
[ 79.509049] scsi4 : SCSI emulation for USB Mass Storage devices
[ 79.509322] usbcore: registered new interface driver usb-storage
[ 79.509329] USB Mass Storage support registered.
[ 79.512401] usb-storage: device found at 2
[ 79.512406] usb-storage: waiting for device to settle before scanning
[ 84.508409] usb-storage: device scan complete
[ 84.509052] scsi 4:0:0:0: Direct-Access Kingston DT 101 G2 1.00 PQ: 0 ANSI: 2
[ 84.509571] scsi: killing requests for dead queue
[ 84.509634] scsi: killing requests for dead queue
[ 84.509690] scsi: killing requests for dead queue
[ 84.509743] scsi: killing requests for dead queue
[ 84.509796] scsi: killing requests for dead queue
[ 84.509848] scsi: killing requests for dead queue
[ 84.509901] scsi: killing requests for dead queue
[ 84.509953] scsi: killing requests for dead queue
[ 84.523114] sd 4:0:0:0: [sdc] 7818184 512-byte logical blocks: (4.00 GB/3.72 GiB)
[ 84.524360] sd 4:0:0:0: [sdc] Write Protect is off
[ 84.524368] sd 4:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 84.524373] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 84.527121] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 84.527134] sdc:
[ 84.527542] sd 4:0:0:0: Attached scsi generic sg4 type 0
[ 84.527887] sdc1
[ 84.529736] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 84.529745] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 793.177039] scsi: killing requests for dead queue
[ 799.772044] usb 2-1: USB disconnect, address 2
[ 1807.120022] usb 2-1: new high speed USB device using ehci_hcd and address 3
[ 1807.770702] usb 2-1: configuration #1 chosen from 1 choice
[ 1807.771629] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1807.771812] usb-storage: device found at 3
[ 1807.771817] usb-storage: waiting for device to settle before scanning
[ 1812.769270] usb-storage: device scan complete
[ 1813.912834] scsi 5:0:0:0: Direct-Access SMI USB DISK 3000 PQ: 0 ANSI: 0 CCS
[ 1813.912917] scsi: killing requests for dead queue
[ 1813.912979] scsi: killing requests for dead queue
[ 1813.913377] scsi: killing requests for dead queue
[ 1813.913440] scsi: killing requests for dead queue
[ 1813.913495] scsi: killing requests for dead queue
[ 1813.913548] scsi: killing requests for dead queue
[ 1813.913601] scsi: killing requests for dead queue
[ 1813.913657] scsi: killing requests for dead queue
[ 1813.914025] sd 5:0:0:0: Attached scsi generic sg4 type 0
[ 1815.642639] sd 5:0:0:0: [sdc] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 1815.643625] sd 5:0:0:0: [sdc] Write Protect is off
[ 1815.643630] sd 5:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 1815.643634] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 1817.104553] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 1817.104561] sdc: sdc1
[ 1817.109284] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 1817.109295] sd 5:0:0:0: [sdc] Attached SCSI removable disk
[ 1840.626576] usb 2-1: reset high speed USB device using ehci_hcd and address 3
[ 1846.524212] usb 2-1: USB disconnect, address 3
[ 1846.524290] sd 5:0:0:0: [sdc] Unhandled error code
[ 1846.524295] sd 5:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 1846.524308] sd 5:0:0:0: [sdc] CDB: Read(10): 28 00 00 3f c7 60 00 00 f0 00
[ 1846.524329] end_request: I/O error, dev sdc, sector 4179808
[ 1846.524396] sd 5:0:0:0: [sdc] Unhandled error code
[ 1846.524400] sd 5:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1846.524406] sd 5:0:0:0: [sdc] CDB: Read(10): 28 00 00 3f c8 50 00 00 10 00
[ 1846.524431] end_request: I/O error, dev sdc, sector 4180048
[ 1846.641939] scsi: killing requests for dead queue
[ 1846.877044] usb 2-1: new high speed USB device using ehci_hcd and address 4
[ 1847.478707] usb 2-1: configuration #1 chosen from 1 choice
[ 1847.479597] scsi6 : SCSI emulation for USB Mass Storage devices
[ 1847.479782] usb-storage: device found at 4
[ 1847.479787] usb-storage: waiting for device to settle before scanning
[ 1852.476213] usb-storage: device scan complete
[ 1852.576837] scsi 6:0:0:0: Direct-Access SMI USB DISK 3000 PQ: 0 ANSI: 0 CCS
[ 1852.576924] scsi: killing requests for dead queue
[ 1852.576985] scsi: killing requests for dead queue
[ 1852.577337] scsi: killing requests for dead queue
[ 1852.577410] scsi: killing requests for dead queue
[ 1852.577464] scsi: killing requests for dead queue
[ 1852.577516] scsi: killing requests for dead queue
[ 1852.577568] scsi: killing requests for dead queue
[ 1852.577620] scsi: killing requests for dead queue
[ 1852.577939] sd 6:0:0:0: Attached scsi generic sg4 type 0
[ 1852.583676] sd 6:0:0:0: [sdc] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 1852.584579] sd 6:0:0:0: [sdc] Write Protect is off
[ 1852.584587] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 1852.584592] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1852.590461] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1852.590473] sdc: sdc1
[ 1852.598222] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1852.598232] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 1856.396027] usb 2-1: reset high speed USB device using ehci_hcd and address 4
[ 1862.296260] usb 2-1: USB disconnect, address 4
[ 1862.296537] sd 6:0:0:0: [sdc] Unhandled error code
[ 1862.296542] sd 6:0:0:0: [sdc] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 1862.296550] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 38 d0 00 00 80 00
[ 1862.296570] end_request: I/O error, dev sdc, sector 14544
[ 1862.296717] FAT: FAT read failed (blocknr 12320)
[ 1862.296749] sd 6:0:0:0: [sdc] Unhandled error code
[ 1862.296754] sd 6:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 1862.296759] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 39 50 00 00 80 00
[ 1862.296776] end_request: I/O error, dev sdc, sector 14672
[ 1862.305803] FAT: FAT read failed (blocknr 872)
[ 1862.307415] FAT: FAT read failed (blocknr 32)
[ 1862.308709] FAT: FAT read failed (blocknr 32)
[ 1862.310297] FAT: FAT read failed (blocknr 32)
[ 1862.343868] scsi: killing requests for dead queue
[ 1862.573047] usb 2-1: new high speed USB device using ehci_hcd and address 5
[ 1863.190773] usb 2-1: configuration #1 chosen from 1 choice
[ 1863.193434] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1863.193843] usb-storage: device found at 5
[ 1863.193848] usb-storage: waiting for device to settle before scanning
[ 1868.192228] usb-storage: device scan complete
[ 1868.292867] scsi 7:0:0:0: Direct-Access SMI USB DISK 3000 PQ: 0 ANSI: 0 CCS
[ 1868.292963] scsi: killing requests for dead queue
[ 1868.293236] scsi: killing requests for dead queue
[ 1868.293314] scsi: killing requests for dead queue
[ 1868.293382] scsi: killing requests for dead queue
[ 1868.293463] scsi: killing requests for dead queue
[ 1868.293524] scsi: killing requests for dead queue
[ 1868.293583] scsi: killing requests for dead queue
[ 1868.293641] scsi: killing requests for dead queue
[ 1868.301631] sd 7:0:0:0: Attached scsi generic sg4 type 0
[ 1868.306219] sd 7:0:0:0: [sdc] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 1868.307347] sd 7:0:0:0: [sdc] Write Protect is off
[ 1868.307355] sd 7:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 1868.307360] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 1868.311592] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 1868.311605] sdc: sdc1
[ 1868.314572] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 1868.314582] sd 7:0:0:0: [sdc] Attached SCSI removable disk
[ 1880.309919] scsi: killing requests for dead queue
Το πρόβλημα παραμένει...
Για δες και δοκιμασε και με αυτον τον τροπο εδω https://help.ubuntu.com/community/Mount/USB